Nearly everybody has their private idea on the subject of Installing A Bathtub.
Installing a tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably tough project. If the old bathtub is readily easily accessible, the project can move easily; if you have to open a wall surface to remove the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the new one. See to it you have certified yourself for the task and also are comfortable attempting it. Instead of working with a professional to take control of a halfway-completed task, it is far better to consider using one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will certainly aid you mount a new tub in your bathroom if you have actually already acquired a new bathtub and don't require to change the arrangement of your previous water system pipelines.
Your tools as well as product list should make up the following:
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the tap features a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its final setting.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the restricted accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the bath tub in the required placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level and changing the feet on the bath tub up until the level reads degree.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water system and also check all joints and also new pipework for leakages and tighten them if needed. Fill the bath tub and additionally examine the overflow outlet and also the typical outlet for leaks.
Finally, repair the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and sealing around the bath tub ought to wait till the bath tub has been used at the very least once as this will settle it into its last setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in place between the faucet as well as the sink. Protect the faucet in position with the producer given backnut. Once the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal tap ports. The previous type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bathroom and the tiling, leading to complications with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in use. The sealant can crack relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly offered on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very focused on A Step-by-Step Guide to Installing a Bathtub and I hope you appreciated our piece. For those who appreciated our page please be sure to pass it around. Many thanks for your time. Kindly come visit our website back soon.
Quote